Parsing bearing installed! Pack a good ascension life, reduce the security hidden danger - bearing knowledge

Rolling bearing instructions 1. When installing the bearing should be uniform stress, not directly hammer. Such as: cooperate with interference is bigger, bearing should be placed on automatic temperature control of air heating furnace or oil furnace, heating temperature control strictly under 120 °. 2. Equipped with nylon cage bearing can in - 40°- 120 ° under long-term continuous stable work, work should not be more than 4 hours at 150 °, the transient temperature peak of up to 180 °. 3. Is not allowed for bearing the warehouse should be clean, dry and chemical products are the same as a storage, relative humidity should not be more than 65%, stored and bearings are not allowed to fall to the ground. Deep groove ball bearing installation use 1. When installing the bearing should be uniform stress, not directly hammer. Such as: cooperate with interference is bigger, bearing should be placed on automatic temperature control of air heating furnace or oil furnace, heating temperature control strictly under 120 °. 2. Equipped with nylon cage bearing can in - 40°- 120 ° under long-term continuous stable work, the work should not be more than 4 hours at 150 °, short peak temperature should not exceed 180 °. 3. Is not allowed for bearing the warehouse should be clean, dry and chemical products are the same as a storage, relative humidity should not be more than 65%, stored and bearings are not allowed to fall to the ground. 4. Inventory bearing cleaned once every other year should resume, rustproof packaging. Angular contact ball bearing using 1 installation. When installing the bearing should be uniform stress, not directly hammer. Such as: cooperate with interference is bigger, bearing should be placed on automatic temperature control of air heating furnace or oil furnace, heating temperature control strictly under 100 °. 2. Equipped with nylon cage bearing can in - 40°- 120 ° under long-term continuous stable work, the work should not be more than 4 hours at 150 °, the transient temperature peak of up to 180 °. 3. Is not allowed for bearing the warehouse should be clean, dry and chemical products are the same as a storage, relative humidity should not be more than 65%, stored and bearings are not allowed to fall to the ground. Spherical roller bearings use 1 installation, users should choose appropriate coordination and according to the requirements of using bearing strength to clearance. After unpacking please proofread bearing code first. 2. In bearing before installation, if need to be within the bearing grease, oil must be clean and right amount. 3. When installation to not directly within the hammer, outer end face and roller advisable, in order to avoid the crack in the inner ring or, small guard. Often users should put the bearing into the heated to 90 ° - in mineral oil 100 ° immediately when loaded on the spindle. For bearing the local burner method of avoid by all means, in the difficult to 'hot charging users should also use the special socket installation. 4. Bearing used in dust should have good sealing device and lubrication, oil cannot be broken. 5. Bearing warehouse should be clean and dry, no environmental pollution, bearing pile does not fall to the ground, packing without damage. Inventory over 1 year of bearings have to clean oil. Use 1 thrust self-aligning roller bearing installation. When installing the bearing should be bearing oil seal to wash again with a clean high quality lubricating oil. 2. When bearing installation, should force uniform, not hammer. Such as the interference fit is larger, should put the bearing into the heated to 90 ° - in mineral oil 100 ° immediately after the installation. 3. For bearing the warehouse should be clean, clean, relative humidity less than 65%. 4. Inventory bearing every should to clean oil once a year, to maintain good oil seal packing. 5 when using bearing, should have good sealing dust control device, and often should check the working condition. Cylindrical roller bearing installation use 1. When the bearing is separation model, user installation according to the need to adjust the clearance. 2. Bearing before use, application of gasoline or kerosene, clean, and maintain good lubrication. 3. Bearing installation, bearing should be pressed into parts, it is forbidden to knock. 4. Bearing place should be clean and ventilated, avoid damp, need to keep long-term bearing, should be rust on a regular basis. Thrust ball bearing installation use 1. Install the bearing should be dismantled when bearing sealing, wash again with a clean high quality lubricating oil. 2. When bearing installation, should force uniform, not hammer. Such as the interference fit is larger, should put the bearing into the heated to 90 ° - in mineral oil 100 ° immediately after the installation. 3. For bearing the warehouse should be clean, clean, relative humidity less than 65%. 4. Inventory bearing every should to clean oil once a year, to maintain good oil seal packing. 5 when using bearing, should have good sealing dust control device, and often should check the working condition.