Bearing assembly resolution! Good to promote life, reduce the safe hidden trouble

Rolling bearings used to clarify 1. Plant bearing should stress on average, not hammer directly. Such as: cooperate with interference is bigger, bearing should be placed on automatic temperature control of air heating furnace or oil furnace, heating temperature control under 120 °. 2. Equipped with nylon stick to frame bearing can be - 40°- 120 ° under long-term continuous stable work, work should not surpass 4 hours at 150 °, the transient temperature peak of up to 180 °. 3. Check bearing warehouse should be clean, dry are not allowed to be a storage with chemical products, should not exceed 65%, relative humidity and bearings are not allowed to fall to the ground storage. Deep groove ball bearing assembly using 1. Plant bearing should stress on average, not hammer directly. Such as: cooperate with interference is bigger, bearing should be placed on automatic temperature control of air heating furnace or oil furnace, heating temperature control under 120 °. 2. Equipped with nylon stick to frame bearing can be - 40°- 120 ° under long-term continuous stable work, the work should not exceed 4 hours at 150 °, short peak temperature should not exceed 180 °. 3. Check bearing warehouse should be clean, dry are not allowed to be a storage with chemical products, should not exceed 65%, relative humidity and bearings are not allowed to fall to the ground storage. 4. Inventory bearing every other year should be to clean again, stop rustproof packaging. Use 1 angular contact ball bearing assembly. Plant bearing should stress on average, not hammer directly. Such as: cooperate with interference is bigger, bearing should be placed on automatic temperature control of air heating furnace or oil furnace, heating temperature control under 100 °. 2. Equipped with nylon stick to frame bearing can be - 40°- 120 ° under long-term continuous stable work, the work should not exceed 4 hours at 150 °, the transient temperature peak of up to 180 °. 3. Check bearing warehouse should be clean, dry are not allowed to be a storage with chemical products, should not exceed 65%, relative humidity and bearings are not allowed to fall to the ground storage. Self-aligning roller bearing device using 1, users should be according to the using request to choose appropriate coordination and bearing strength to clearance. Please correct bearing code after unpacking. 2. In front of the bearing assembly, if need to add grease in the bearing, oil must be clean, right amount. 3. Device does not directly within the hammer, outer end face and roller advisable, in order to avoid the crack in the inner ring or, small guard. Often users should put the bearing into the heated to 90 ° - in mineral oil 100 ° immediately on the spindle. Avoid by all means is adopted for bearing part of the burner method, the difficult to when the hot charging users should use the special socket device. 4. Bearing used in dust should have good sealing installation and smooth, not oil. 5. Bearing warehouse should be clean and dry, no environmental pollution, bearing pile does not fall to the ground, packing without damage. Inventory over 1 year of bearings have to clean the oil. Use 1 thrust spherical roller bearing assembly. Device when bearing should be bearing oil seal to wash again with a clean smooth oil quality. 2. Plant bearing, should stress on average, not hammer. Such as the interference fit is larger, should put the bearing into the heated to 90 ° - in mineral oil 100 °, the device immediately. 3. Check bearing warehouse should be clean, clean, are no more than 65% relative humidity. 4. Inventory bearing every other year should to clean oil, oil seal packaging adhere to the good. When you use bearing, should have good sealing dust installation, and should be regularly check the work situation. Use 1 cylindrical roller bearing assembly. When the bearing is separation model, user device can be adjusted according to the demand to clearance. 2. Bearing before use, application of gasoline or kerosene wash clean, smooth and adhere to the good. 3. Bearing assembly, bearing should be pressed into parts, it is forbidden to knock. 4. Bearing cloakroom should be clean and ventilated, prevent moisture, to long-term preservation of bearing, should be rust on a regular basis. Use 1 thrust ball bearing assembly. Device bearing should be removed when bearing sealing, wash again with a clean smooth oil quality. 2. Plant bearing, should stress on average, not hammer. Such as the interference fit is larger, should put the bearing into the heated to 90 ° - in mineral oil 100 °, the device immediately. 3. Check bearing warehouse should be clean, clean, are no more than 65% relative humidity. 4. Inventory bearing every other year should to clean oil, oil seal packaging adhere to the good. When you use bearing, should have good sealing dust installation, and should be regularly check the work situation.